( Item # = PG0144 )  General Electric LM6000 Gas Turbine Generator set

GE LM6000 PD Gas Turbine Generator  60Hz (New)  -  - General Electric LM6000 Gas Turbine Generator set 60Hz Generator (Brush - Meidensha) 13,800 Volt, 3600 RPM, 0.85pf. Low maintenance brushless excitation system suitable for Class I, Group D, Div 2 areas.  Neutral and line cubicles with CTs, surge protectors, power system stabilizer, and lightning arrestors -USA  -

 Natural Gas fuel system, complete and self-contained on the unit, with connection on the baseplate for customer's filtered, regulated fuel supply
at 675 psig * 20 psig.

 Generator (Brush - Meidensha) 13,800 Volt, 60 Hz, 3600 RPM, 0.85pf. Low maintenance brushless excitation system suitable for Class I, Group D, Div 2 areas.  Neutral and line cubicles with CTs, surge protectors, power system stablizer, and lightning arrestors,

  I-beam baseplates for turbine, generator and unit mounted accessories.

 Acoustic enclosure for gas turbine and generator.  Redundant ventilation systems, and AC internal lighting .

 Multi stage air inlet filtration system for both gas turbine and generator,
including weather hoods, inlet screen, pre-filter, final barrier filter, intake silencer, and standard ducting to plenum chamber.  Filterhouse ladders and platforms are included.

 Electro-hydraulic start system.

 Separate oil systems for gas turbine and generator, including duplex filters, duplex water/oil coolers, stainless steel piping, and stainless steel reservoirs.  Auxiliary skid must be installed by others in a heated enclosure.

            Unit control panel for indoor mounting in a controlled environment, including microprocessor fuel management and sequencing system, generator metering, Bently Nevada vibration monitoring, CRT annunciation of alarms and shutdowns, and Ethernet or Modbus interface to customer’s DCS for The LM6000PD.

 I/O cubicle mounted on gas turbine enclosure.

 24V DC control system NI Cad battery with dual battery chargers.
 

 Fire and gas detection and extinguishing system, serving both turbine and generator compartments, complete with 24V DC Ni Cad battery and charger.

 “Soak wash” system (off-line) for simple cycle service, and on-line water wash system.

 Generator testing at factory to IEEE or IEC standards.  Gas turbine
performance testing on factory dynomometer;  Gas Turbine package static test.  No full load factory string test of the generator set.

 Six sets of drawing and data packages, O & M manuals.

 LM6000 gen set familiarization / basic operator training course, 5 days at Jacintoport TX or on-site for up to 10 customer personnel.  Customer travel expenses by the customer.

 GE Prolec GSU (generator step-up) transformer, 13.8/138 kv.

B. OPTIONAL EQUIPMENT AND SERVICES
     (I) included in base price    (S) Quoted separately (N) Not Included

(  N ) Option B - Alternate voltage or power factor             KV @             pf
(  N ) Option C - Water cooled generator (TEWAC) for >85°F cooling water
(  N ) Option D - Fin-Fan oil coolers
(  I ) Option E - Alternate side location for piping connections and turbine removal
(  I )  Option F - Alternate side termination, lineside & neutral cubicles
( N ) Option G –Synchronous Condenser Capability
( N ) Option H - Dual fuel system, simplex fuel boost pump skid, simplex fuel forwarding skid
for installation by others in heated areas if required
( N )   Option I - Water injection metering system (NOx control with gaseous, liquid or dual fuel
  systems)  Simplex boost pump
( N )   Option J -  Sprint (Spray Intercooling) Power Boost System with simplex boost pump.
( N )  Option K - Steam injection metering system (NOx control with gaseous fuel system only)
( I )  Option L - Dry, Low Emissions (DLE) (NOx, CO and HC control without water or steam
  injection…..available for gaseous fuel only)
( N )  Option M - Evaporative cooling, non recirculating design
( I )   Option N - Inlet Air Anti-Ice System for water glycol, includes only heating coil in the air filter, water glycol heating and pumping system is by others.
( N )   Option O - Inlet Air Chilling System  (Coil only)
( N )   Option P – Standard Exhaust Assembly with 45’ stack, EPA Ports and Platforms & Ladders
( I )    Option Q - Winterization
(  N )   Option R - Black Start System
( N)  Option S - Modular Control Room, aproximately 25 ft long x 14 ft wide with unit control
 panel, MCC and 24 VDC batteries and chargers for controls and fire protection
(  N)  Option T – Switchgear with CT’s and PT’s, 3,000 Amp,  1000 MVA rating,  with NEMA 3R outdoor enclosure
(  N)  Option U -Unit Motor Control Center – in the Modular Control Room to supply power to 3 phase AC motors for GTG equipment rated up to and including 200 kW, 480 Volt
(  I )    Option V –Standard GE PROLEC GSU Transformer, 45/60/75 MVA OA/FA/FA high voltage of 138 KV wye connection and low voltage of 13.8 kV delta connection (sidewall bushings) with no load tap changer.  Installation and assembly of the transformer is by others.  Initial supply of oil will be shipped to the site by tanker, filling is by others.
(  I )   Option W -Power System Stabilizer for electric generator  (excludes electrical analysis
                              of customer grid connection)
( I ) Guard Filter, for Poplar fuzz the customer should add  a screen mesh in the field on the face of these filters.
( N) 85 db(A) silencing, average 3’ away and 5’ high around the unit

( N ) 125 V batteries and charger for generator Breaker
 

II. EXCLUSIONS

            The items listed below are excluded from our offering.  Any other equipment or services
            not described in the GE Aero Energy Products written proposal are
            also excluded.

- Fuel, fluids and chemicals
- Fuel storage tanks, treatment, heating and forwarding equipment
- Fuel gas compression, filtration, heating etc.
- Water treatment and purification equipment
- Deaeration and chemical injection equipment
- Heat recovery boiler, transition piece and exhaust expansion joint
- Boiler feed pump and auto level control assembly
- Automatic blowdown controls
- Absorption chiller and chilled water supply system
- Buildings, foundations and foundation embedments
- Filter house support structure other than standard
- High voltage transformer(s) other than the GSU transformer, switchgear and associated equipment
- Auxiliary Transformer
- Distributed plant control or remote control panels
- Balance of plant and energy optimization controls
- Desuperheater equipment
- Steam turbine generator set
- Steam turbine condenser and condensate pumping equipment
- Cooling tower and circulating water system
- Interconnecting piping, conduit, and wiring between equipment modules
- Power plant calibration tools and ordinary hand tools
- Off loading of equipment at jobsite
- Yard light and fences
- Spare parts other than start-up spares
- Supervision or technical direction at jobsite

Items marked with an I on Pages 5 & 6 supercede this exclusion list.
 

III. PRICING  OF  EQUIPMENT

A. BASIS OF PRICING

  1. Validity

 This proposal is valid for acceptance, subject to prior sale, by execution of  an Agreement in Principle and receipt of payment.  Sale is subject to consent of  GE Packaged Power, Inc. (“GE”)

  2. Taxes and Duty

 No GST, PST, sales or use taxes, or Duty have been included in this quotation.   The prices quoted exclude any Federal, State, or local taxes, or fees which may be associated with the purchase of equipment and/or services.

  3. Firm Price

 The prices quoted are not subject to escalation during the quoted manufacturing cycle.
                                    If payment or delivery is delayed by buyer, the price shall be adjusted to reflect the cost of money during delay period until payment has been made current.

  B. PRICE

  All Prices are in US $ Ex Factory.

  Our pricing references the scope of work described.

 One LM6000PD gas turbine generator set including optional equipment specified as included (I) in Section I.

D. SHIPMENT  SCHEDULE

February 28, 2002 is the date for Shipment.

E. TERMS AND CONDITIONS OF SALE

The terms and conditions of sale will be negotiated in good faith between  and Purchaser.  Sale is subject to consent by GE.  Title transfer will occur on notice of ready to ship by GE.
 

IV. LM6000  PERFORMANCE

 A Performance Guarantee Sheet will be prepared upon confirmation of site conditions and Customer’s selection of the point to be used for Guarantee performance.

V. PRODUCT SPECIFICATION

 A Product Specification binder for the LM6000 generator set is available upon request.